[Aug-2026] F5-CA F5CAB2 Exam Practice Dumps
2026 F5CAB2 Premium Files Test pdf - Free Dumps Collection
NEW QUESTION # 30
A development team needs to apply a software fix and troubleshoot one of its servers. The BIG-IP Administrator needs to immediately remove all connections from the BIG-IP system to the back-end server.
The BIG-IP Administrator checks the Virtual Server configuration and finds that a persistence profile is assigned to it. What should the BIG-IP Administrator do to meet this requirement?
- A. Set the pool member to a Forced Offline state and manually delete existing connections through the command line
- B. Set the pool member to a Forced Offline state
- C. Set the pool member to a Disabled state and manually delete existing connections through the command line
- D. Set the pool member to a Disabled state
Answer: A
Explanation:
Managing the lifecycle of a pool member requires understanding the difference between "Disabled" and
"Forced Offline" states, especially when persistence is involved.
* Disabled (User-Disabled): This state allows existing connections and persistent sessions to continue until they naturally time out or are closed by the client/server. It only preventsnewsessions from being established.
* Forced Offline: This state is more restrictive; it allows existing connections to complete butrejectsall new connections, including those with existing persistence records.
* Immediate Removal: Neither "Disabled" nor "Forced Offline" will instantly kill currently active, established TCP connections. To meet the requirement of "immediately" removing all connections, the administrator must first set the member toForced Offline(to prevent persistence from bringing in new traffic) and then use the command line (e.g., tmsh delete sys connection ss-server-addr [IP]) to clear the current connection table entries.
NEW QUESTION # 31
The BIG-IP appliance fails to boot. The BIG-IP Administrator needs to run the End User Diagnostics (EUD) utility to collect data to send to F5 Support.
Where can the BIG-IP Administrator access this utility?
- A. Management Port
- B. Console Port
- C. Internal VLAN interface
- D. External VLAN interface
Answer: B
NEW QUESTION # 32
Which three iRule events are likely to be seen in iRules designed to select a pool for load balancing? (Choose three.)
- A. HTTP_RESPONSE
- B. SERVER_CONNECTED
- C. SERVER_DATA
- D. HTTP_REQUEST
- E. CLIENT_DATA
- F. SERVER_SELECTED
- G. CLIENT_ACCEPTED
Answer: D,E,G
Explanation:
12
In the BIG-IP system, pool selection must occur on the client-side of the connection, before the system attempts to connect to a pool 3member. The events listed 4are the primary entry points for making these decisions:
* CLIENT_ACCEPTED (E): This is a Layer 4 event triggered when the BIG-IP accepts a TCP connection. It is the earliest point where a pool can be assigned based on the client's source IP address or the destination port.
* CLIENT_DATA (A): This event is triggered when the system receives a "chunk" of data on the client- side. It is often used for non-HTTP protocols (like custom TCP protocols) to inspect the payload and select a pool based on its contents.
* HTTP_REQUEST (C): This is a Layer 7 event. It occurs once the BIG-IP has fully parsed the HTTP headers. This is the most common event for pool selection, allowing the administrator to route traffic based on the URI, Host header, or cookies.
Events like SERVER_SELECTED or SERVER_CONNECTED occur after the load balancing decision has already been made, and HTTP_RESPONSE or SERVER_DATA occur after the server has already started communicating back, making them too late for initial pool selection.
NEW QUESTION # 33
A BIG-IP Administrator is making adjustments to an iRule and needs to identify which of the 235 virtual server configured on the BIG-IP device will be affected. How should the administrator obtain this information in an effective way? (Choose one answer)
- A. Local Traffic > Pools
- B. Local Traffic > iRules
- C. Local Traffic > Network Map
- D. Local Traffic > Virtual Server
Answer: C
Explanation:
In a large-scale BIG-IP environment with hundreds of virtual servers, the Network Map is the most effective tool for visualizing and auditing the relationships between various ADC objects.
* The Network Map Functionality: The Network Map provides a hierarchical view of the local traffic objects. It allows an administrator to see the status and dependencies of Virtual Servers, Pools, Pool Members, and associated iRules all in one screen.
* Search and Filter: By navigating to Local Traffic > Network Map, the administrator can use the Advanced Filter. This feature allows for searching specifically for an iRule name or a string within an iRule definition. Once the filter is applied, the system displays only the Virtual Servers that are associated with that specific iRule.
* Efficiency: While the "Virtual Server List" (Option D) can be customized to show columns for iRules, it is often cumbersome to scroll through hundreds of entries. The "iRules List" (Option B) displays the scripts themselves but does not provide a reverse-lookup list of all associated virtual servers in a single view as efficiently as the Network Map.
* Summary of Relationships: The Network Map is specifically designed to answer the question, "What is this object connected to?" making it the primary administrative interface for impact analysis during configuration changes.
NEW QUESTION # 34
A BIG-IP Administrator is informed that traffic on interface 1.1 is expected to increase beyond the maximum bandwidth capacity of the link. There is a single VLAN on the interface.
What should the BIG-IP Administrator do to increase the total available bandwidth? (Choose one answer)
- A. Set the media speed of interface 1.1 manually
- B. Increase the MTU on the VLAN using interface 1.1
- C. Create a trunk object with two interfaces
- D. Assign two interfaces to the VLAN
Answer: C
Explanation:
On BIG-IP systems, physical interface bandwidth is fixed by the link speed (for example, 1GbE or 10GbE).
When traffic demand exceeds the capacity of a single interface, BIG-IP provides link aggregation through trunks.
Key concepts involved:
* InterfacesA single physical interface (such as 1.1) is limited to its negotiated link speed. You cannot exceed this capacity through software tuning alone.
* Trunks (Link Aggregation)A trunk combines multiple physical interfaces into a single logical interface.
* BIG-IP supports LACP and static trunks.
* Traffic is distributed across member interfaces, increasing aggregate bandwidth and providing redundancy.
* VLANs are then assigned to the trunk, not directly to individual interfaces.
Why option B is correct:
* Creating a trunk with two interfaces allows BIG-IP to use both physical links simultaneously.
* This increases total available bandwidth (for example, two 10Gb interfaces # up to 20Gb aggregate capacity).
* This is the documented and supported method for scaling bandwidth on BIG-IP.
Why the other options are incorrect:
* A. Increase the MTUMTU changes affect packet size and efficiency, not total bandwidth capacity.
* C. Assign two interfaces to the VLANBIG-IP does not support assigning a VLAN to multiple interfaces directly. VLANs must be associated with one interface or one trunk.
* D. Set the media speed manuallyMedia speed can only be set up to the physical capability of the interface and connected switch port. It cannot exceed the hardware limit.
Conclusion:
To increase total available bandwidth on BIG-IP when a single interface is insufficient, the administrator must create a trunk object with multiple interfaces and move the VLAN onto the trunk. This aligns directly with BIG-IP data plane design and best practices.
NEW QUESTION # 35
Which statement is true concerning iRule events?
- A. All iRule events are appropriate at any point in the client-server communication.
- B. All iRule events relate to HTTP processes.
- C. All client traffic has data that could be used to trigger iRule events.
- D. If an iRule references an event that doesn't occur during the client's communication, the client's connection will be terminated prematurely.
Answer: C
Explanation:
iRules are event-driven scripts that allow for advanced traffic manipulation.
* Universality of Events:Every packet that passes through t21he BIG-IP data plane triggers events. Even non-HTTP traffic triggers events such as CLIENT_ACCEPTED (when the TCP connection is established22) or CLIENT_DATA (when raw data is received). Therefore, all client traffic-regardless of protocol-has data that can trigger an iRule event.
* Event Specificity:Events are not universal (Option C is false). For example, HTTP_REQUEST only occurs after a full HTTP header is parsed. You cannot trigger an HTTP_RESPONSE event before a request has been sent to a server.
* Protocol Agnostic:iRules are not limited to HTTP (Option A is false); they can handle TCP, UDP, DNS, FTP, SIP, and more.
* Error Handling:If an iRule references an event that never triggers (e.g., an HTTP_REQUEST event in a purely TCP virtual server), the iRule code for that event simply never executes. It doesnotterminate the connection (Option D is false).
NEW QUESTION # 36
A standard virtual server has been associated with a pool with multiple members. Assuming all other settings are left at their defaults, which statement is always true concerning traffic processed by the virtual server?
- A. The IP addresses used in the clientside connection are the same as the IP addresses used in the serverside connection.
- B. The client IP address is unchanged between the client side connection and the serverside connection.
- C. The TCP ports used in the client side connection are the same as the TCP ports serverside connection.
- D. The server IP address is unchanged between the client side connection and the serverside connection.
Answer: B
NEW QUESTION # 37
A BIG-IP Administrator has a cluster of devices.
What should the administrator do after creating a new Virtual Server on device 1? (Choose one answer)
- A. Create a new cluster on device 1
- B. Synchronize the settings of the group to device 1
- C. Create a new virtual server on device 2
- D. Synchronize the settings of device 1 to the group
Answer: D
NEW QUESTION # 38
When upgrading a BIG-IP redundant pair, what happens when one system has been updated but the other has not?
- A. The first system to be updated will assume the Active role.
- B. The older system will issue SNMP traps indicating a communication error with the partner.
- C. This is not possible since both systems are updated simultaneously.
- D. Synching should not be performed.
Answer: D
NEW QUESTION # 39
A BIG-IP Administrator makes a configuration change to a Virtual Server on the Standby device of an HA pair. The HA pair is currently configured with Auto-Sync enabled. What effect will the change have on the HA pair configuration? (Choose one answer)
- A. The change will be propagated next time a configuration change is made on the Active device.
- B. The change will be undone when Auto-Sync propagates the config to the Standby device.
- C. The change will take effect when Auto-Sync propagates the config to the HA pair.
- D. The change will be undone next time a configuration change is made on the Active device.
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Data Plane Concepts documents:
In a BIG-IP high availability (HA) configuration, Auto-Sync is a device trust feature that automatically synchronizes configuration changes from the Active device to the Standby device within a Sync-Failover device group.
Key principles from BIG-IP Administration Data Plane Concepts:
The Active device is always the authoritative source of configuration
Configuration changes are intended to be made only on the Active device With Auto-Sync enabled, any time the Active device configuration changes, the system automatically pushes the configuration to all Standby members of the device group Configuration changes made directly on a Standby device are not preserved In this scenario:
The administrator modifies a Virtual Server on the Standby device
That change is local only and does not alter the device group's synchronized configuration When Auto-Sync next runs (triggered by a change on the Active device or an internal sync event), the Active device configuration overwrites the Standby configuration As a result, the configuration change made on the Standby device is undone.
Why the Other Options Are Incorrect:
A - The change is not undone only when another change is made; it is undone during the next Auto-Sync operation B - Changes made on the Standby device are never propagated to the Active device D - Auto-Sync does not merge or promote Standby changes into the HA pair configuration Best Practice Reinforced:
Always perform configuration changes on the Active BIG-IP device when Auto-Sync is enabled to ensure consistent and predictable HA behavior.
NEW QUESTION # 40
In the GUI, where should the BIG-IP Administrator configure an existing VLAN named external to a specific interface as untagged?
- A. Network - VLANs -> VLAN List -> external -> interfaces
- B. Network -> VLANs -> VLAN List -> internal -> interfaces
- C. Network -> VLANs -> VLAN List -> create -> external
Answer: A
Explanation:
In the BIG-IP system, VLANs are the logical entities that group physical interfaces or trunks together. To modify how a VLAN interacts with an interface, the administrator must navigate to the specific VLAN configuration object.
* VLAN List:This section displays all existing VLANs configured on the system.
* Interface Association:Within the properties of a specific VLAN (in this case, "external"), there is an Interfacessection. This is where physical ports or trunks are assigned to the VLAN.
* Tagging Status:For each associated interface, the administrator can choose betweenTagged(802.1Q) or Untagged.
* Untagged:The interface will treat incoming traffic without a VLAN header as part of this VLAN, and outgoing traffic will not have a VLAN tag added. An interface can only be "Untagged" for one VLAN.
* Tagged:Allows an interface to carry traffic for multiple VLANs simultaneously by using 802.1Q headers.
NEW QUESTION # 41
The BIG-IP Administrator wants to provide quick failover between the F5 LTM devices that are configured as an HA pair with a single Self IP using the MAC Masquerade feature. The administrator configures MAC masquerade for traffic-group-1 using the following command:
`tmsh modify /cm traffic-group traffic-group-1 mac 02:12:34:56:00:00`
However, the Network Operations team identifies an issue with using the same MAC address across multiple VLANs. As a result, the administrator enables Per-VLAN MAC Masquerade to ensure a unique MAC address per VLAN by running:
`tmsh modify /sys db tm.macmasqaddr_per_vlan value true`
What would be the resulting MAC address on a tagged VLAN with ID 1501? (Choose one answer)
- A. 02:12:34:56:dd:05
- B. 02:12:34:56:15:01
- C. 02:12:34:56:05:dd
- D. 02:12:34:56:01:15
Answer: C
Explanation:
In BIG-IP high availability (HA) configurations, MAC Masquerade is used to speed up failover by allowing traffic-group-associated Self IPs to retain the same MAC address when moving between devices. This prevents upstream switches and routers from having to relearn ARP entries during a failover event, resulting in near-instant traffic recovery.
By default, MAC masquerade applies one MAC address per traffic group, regardless of how many VLANs the traffic group spans. This can create problems in some network designs because the same MAC address appearing on multiple VLANs may violate network policies or confuse switching infrastructure.
To address this, BIG-IP provides Per-VLAN MAC Masquerade, enabled by the database variable:
`tm.macmasqaddr_per_vlan = true`
When this feature is enabled:
BIG-IP derives a unique MAC address per VLAN
The base MAC address configured on the traffic group remains the first four octets The last two octets are replaced with the VLAN ID expressed in hexadecimal The VLAN ID is encoded in network byte order (high byte first, low byte second)
### VLAN ID Conversion:
VLAN ID: 1501 (decimal)
Convert to hexadecimal:
1501## = 0x05DD
High byte: 05
Low byte: DD
### Resulting MAC Address:
Base MAC: `02:12:34:56:00:00`
Per-VLAN substitution # last two bytes = `05:DD`
Final MAC address:
`02:12:34:56:05:dd`
### Why the Other Options Are Incorrect:
A (01:15) - Incorrect hexadecimal conversion of 1501
B (dd:05) - Byte order reversed (little-endian, not used by BIG-IP)
D (15:01) - Uses decimal values instead of hexadecimal
### Key BIG-IP HA Concept Reinforced:
Per-VLAN MAC Masquerade ensures Layer 2 uniqueness per VLAN while preserving the fast failover benefits of traffic groups, making it the recommended best practice in multi-VLAN HA deployments.
NEW QUESTION # 42
The diagram below shows the TCP connection setup for an application.
Which of the following virtual server types applies? (Choose one answer)
- A. Forwarding IP virtual server
- B. Standard virtual server
- C. Stateless virtual server
Answer: A
Explanation:
The diagram illustrates a specific TCP handshake sequence where the BIG-IP system acts as a transparent forwarder rather than a full proxy. The key indicators that identify this as aForwarding (IP) virtual server are as follows:
* Initial Packet Processing: The diagram explicitly states that the LTM evaluates the packet lookingonly at the destination IP address. This is the fundamental characteristic of a Forwarding IP virtual server, which uses the system's routing table to make forwarding decisions instead of load balancing to a pool of members.
* Handshake Sequence: Unlike aStandardvirtual server, which completes the three-way handshake with the client (SYN, SYN-ACK, ACK)beforeinitiating a separate connection to the server, the Forwarding IP virtual server passes the client's originalSYNpacket directly to the destination node.
* Response Timing: The BIG-IP system waits for theSYN-ACKfrom the destination node before it sends a SYN-ACK back to the client. It essentially "passes through" the handshake signals while still maintaining a state entry in the connection table to track the flow.
* Packet-by-Packet Logic: While it tracks the state, it does not perform address translation (unless SNAT is specifically configured) or deep packet inspection like a full proxy would.
Why other options are incorrect:
* Standard virtual server: A Standard virtual server is a "full proxy." It would finish the handshake with the client first and only then open a second, independent TCP connection to the backend server.
* Stateless virtual server: A stateless virtual server does not track connections in the connection table.
The diagram shows the system meticulously passing sequence numbers ($seq\_num$) and acknowledgment numbers ($ack\_num$) between the two sides, which requires stateful tracking of the TCP flow.
NEW QUESTION # 43
An application is configured so that the same pool member must be used for an entire session, as well as for HTTP and FTP traffic. A user reports that a session has terminated, and the user must restart the session. The BIG-IP Administrator determines that the active BIG-IP device failed over to the standby BIG-IP device.
Which configuration settings should the BIG-IP Administrator verify to ensure proper behavior when BIG-IP failover occurs?
- A. Stateful failover and network failover detection
- B. syn-cookie insertion threshold and connection low-water mark
- C. Persistence mirroring and Match Across Services
- D. Cookie persistence and session timeout
Answer: C
Explanation:
In this scenario, two specific High Availability and Persistence requirements must be met to ensure session continuity during a failover.
* Persistence Mirroring:By default, persistence records (which map a client to a specific server) exist only on the memory of the active BIG-IP. If a failover occurs, the standby unit has no knowledge of these sessions and will re-load-balance the client, likely to a different server. EnablingPersistence Mirroringensures that the persistence table is synchronized in real-time to the standby peer.
* Match Across Services:The requirement specifies that the session must persist across bothHTTPand FTP. These are different Virtual Servers (and likely different ports). TheMatch Across Servicessetting in the persistence profile allows the BIG-IP to use the same persistence record for any Virtual Server that shares the same IP address and pool, regardless of the service port.
NEW QUESTION # 44
Which two statements describe differences between the active and standby systems? (Choose two.)
- A. Floating selfIP addresses are hosted only by the active system.
- B. Virtual server addresses are hosted only by the active system.
- C. Failover triggers only cause changes on the active system.
- D. Configuration changes can only be made on the active system.
- E. Monitors are performed only by the active system.
Answer: A,B
NEW QUESTION # 45
The network architecture for a BIG-IP consists of an external VLAN and an internal VLAN with two interfaces connected to the upstream switch. The design requires fault tolerance in the case that one of the interfaces is down. Which deployment architecture meets these requirements? (Choose one answer)
- A. Two network trunks each with one VLAN and LACP enabled, and both VLANs configured as tagged
- B. One network trunk with both VLANs and LACP enabled, and both VLANs configured as untagged
- C. One network trunk with both VLANs and LACP enabled, and both VLANs configured as tagged
- D. Two network trunks each with one VLAN and LACP disabled, and one VLAN configured as tagged and one VLAN configured as untagged
Answer: C
Explanation:
To meet the requirement of fault tolerance when one interface goes down, BIG-IP must use link aggregation so that loss of a single physical link does not isolate the VLAN(s).
How the objects relate (data plane view)
* Interfaces = physical links.
* Trunk (LACP) = bundles multiple interfaces into one logical link that provides redundancy (and possibly bandwidth aggregation).
* VLANs are assigned to interfaces or trunks. If you need multiple VLANs on the same trunk, they must use 802.1Q tagging (because you can only have one untagged VLAN per interface/trunk).
* Self IPs are then placed on the VLANs to provide BIG-IP presence and routing/ARP functions, but self IPs are not what provides link resiliency-the trunk does.
Why Option D is correct
* You have two physical interfaces and you want resiliency if one fails # put both interfaces into one trunk with LACP enabled.
* You need both external and internal VLANs on those same two links # both VLANs should be configured as tagged on that trunk, so they can coexist on the same aggregated link.
* If either physical interface fails, the trunk remains up via the remaining interface, keeping both VLANs operational.
Why the other options are incorrect
* A: Two VLANs cannot both be untagged on the same trunk/interface. Only one untagged VLAN is possible; additional VLANs must be tagged.
* B: Two trunks "each with one VLAN" would typically mean splitting VLANs across separate trunks.
With only two interfaces total, that becomes one interface per trunk-if one interface goes down, the VLAN on that interface is down (no redundancy for that VLAN).
* C: Same redundancy problem as B, and disabling LACP removes the negotiated aggregation behavior expected when the switch engineer specifically requested LACP.
NEW QUESTION # 46
A BIG-IP Administrator explicitly creates a traffic group on a BIG-IP device. Which two types of configuration objects can be associated with this traffic group? (Choose two.)
- A. Virtual Addresses
- B. Application Instances
- C. iRules
- D. Floating Self IPs
- E. VLANs
Answer: A,D
Explanation:
ATraffic Groupis a collection of related configuration objects that fail over together from one BIG-IP device to another. Only "floating" objects can be members of a traffic group.
* Virtual Addresses (C):A virtual address (the IP part of a Virtual Server) is a floating object. It is assigned to a traffic group so that the entire IP moves to the standby unit during a failover.
* Floating Self IPs (E):These are used as gateways for backend servers or SNAT addresses. By associating them with a traffic group, they remain reachable by the backend network regardless of which BIG-IP is currently active.
Why other options are incorrect:
* iRules (A):iRules are configuration logic files; they are synchronized across devices but are not
"hosted" by a traffic group.
* VLANs (D):VLANs are local to the hardware interfaces/trunks of each specific device and do not fail over.
NEW QUESTION # 47
When upgrading a BIG-IP redundant pair, what happens when one system has been updated but the other has not?
- A. The first system to be updated will assume the Active role.
- B. The older system will issue SNMP traps indicating a communication error with the partner.
- C. This is not possible since both systems are updated simultaneously.
- D. Synching should not be performed.
Answer: D
Explanation:
The F5 BIG-IP upgrade process for HA pairs requires a specific "staggered" approach to maintain uptime.
* Version Mismatch: When one unit is upgraded to a newer version of TMOS (e.g., from 15.1 to 16.1), it enters a26 "Version Mismatch" 27state with its peer.
* Configuration Sync: Because the configuration schemas between different versions are often incompatible, ConfigSync should not be performed. Attempting to sync a newer configuration to an older system (or vice-versa) can cause configuration corruption or system instability.
* Failover Capability: Generally, a pair with a version mismatch can still fail over to ensure traffic continuity during the upgrade window, but administrative changes and syncs must be paused until both units are on the same version.
NEW QUESTION # 48
The BIG-IP Administrator wants to provide quick failover between the F5 LTM devices that are configured as an HA pair with a single Self IP using the MAC Masquerade feature. The administrator configures MAC masquerade for traffic-group-1 using the following command:
`tmsh modify /cm traffic-group traffic-group-1 mac 02:12:34:56:00:00`
However, the Network Operations team identifies an issue with using the same MAC address across multiple VLANs. As a result, the administrator enables Per-VLAN MAC Masquerade to ensure a unique MAC address per VLAN by running:
`tmsh modify /sys db tm.macmasqaddr_per_vlan value true`
What would be the resulting MAC address on a tagged VLAN with ID 1501? (Choose one answer)
- A. 02:12:34:56:dd:05
- B. 02:12:34:56:15:01
- C. 02:12:34:56:05:dd
- D. 02:12:34:56:01:15
Answer: C
NEW QUESTION # 49
What type of virtual server will have a destination IP address of 0.0.0.0 and listen on a specific VLAN for requests?
- A. Forwarding (Layer 2)
- B. Wildcard
- C. Standard
- D. Forwarding (IP)
Answer: B
Explanation:
In BIG-IP LTM, aWildcardvirtual server is defined by using a destination IP address of 0.0.0.0. These virtual servers are designed to handle traffic that does not match any more specific Virtual Server destination address.
* 0.0.0.0 Destination:This address acts as a "catch-all" for IP traffic.
* VLAN Specificity:While the destination address is generic, a Wildcard virtual server is typically restricted to a specificVLAN(such as the Internal VLAN) to process outbound traffic from backend servers.
* Service Ports:A wildcard virtual server can be configured for a specific port (e.g., 0.0.0.0:80) or for all ports (0.0.0.0:0).
* Data Plane Usage:It is commonly used for transparently intercepting outbound traffic for the purpose of Source NAT (SNAT), bandwidth shaping, or directing traffic to a gateway pool.
NEW QUESTION # 50
A BIG-IP Administrator has a cluster of devices.
What should the administrator do after creating a new Virtual Server on device 1? (Choose one answer)
- A. Create a new cluster on device 1
- B. Synchronize the settings of the group to device 1
- C. Create a new virtual server on device 2
- D. Synchronize the settings of device 1 to the group
Answer: D
Explanation:
Comprehensive and Detailed Explanation (BIG-IP Administration - Data Plane Concepts):
In a BIG-IP device service cluster, configuration objects such as virtual servers, pools, profiles, and iRules are maintained through configuration synchronization (config-sync).
Key BIG-IP concepts involved:
Device Service Cluster (DSC)
A cluster is a group of BIG-IP devices that share configuration data. One device is typically used to make changes, which are then synchronized to the rest of the group.
Config-Sync Direction Matters
Changes are made on a local device
Those changes must be pushed to the group
The correct operation is "Sync Device to Group"
Why C is correct:
The virtual server was created only on device 1
Other devices in the cluster do not yet have this object
To propagate the new virtual server to all cluster members, the administrator must synchronize device 1 to the group Why the other options are incorrect:
A . Synchronize the settings of the group to device 1
This would overwrite device 1's configuration with the group's existing configuration and may remove the newly created virtual server.
B . Create a new cluster on device 1
The cluster already exists. Creating a new cluster is unnecessary and disruptive.
D . Create a new virtual server on device 2
This defeats the purpose of centralized configuration management and risks configuration drift.
Conclusion:
After creating a new virtual server on a BIG-IP device that is part of a cluster, the administrator must synchronize the configuration from that device to the group so all devices share the same ADC application objects.
NEW QUESTION # 51
A virtual server is listening at 10.10.1.100:80 and has the following iRule associated with it:
when HTTP_REQUEST { if { [HTTP::header UserAgent] contains "MSIE" }
{ pool MSIE_pool }
else { pool Mozilla_pool }
If
a user connects to http://10.10.1.100/foo.html and their browser does not specify a UserAgent, which pool will receive the request?
- A. Mozilla_pool
- B. MSIE_pool
- C. Unknown. The pool cannot be determined from the information provided.
- D. None. The request will be dropped.
Answer: A
NEW QUESTION # 52
A BIG-IP Administrator wants to add a new Self IP to the BIG-IP device. Which item should be assigned to the new Self IP being configured?
- A. Trunk
- B. Route
- C. VLAN
- D. Interface
Answer: C
Explanation:
ASelf IPis an IP address on the BIG-IP system that you associate with a specificVLAN.
* VLAN Association:A Self IP cannot exist independently; it must be bound to a VLAN to define which network segment the BIG-IP can communicate with.
* Layer 2 to Layer 3 Mapping:While a VLAN is associated with physical interfaces or trunks (Layer 2), the Self IP provides the Layer 3 identity for the BIG-IP on that VLAN.
* Traffic Processing:Self IPs are used by the BIG-IP for health checking backend servers, acting as a default gateway for servers, and for HA heartbeat communication.
NEW QUESTION # 53
An ecommerce company is experiencing latency issues with online shops during Black Friday's peak season. The BIG-IP Administrator detects an overall high CPU load on the BIG-IP device and wants to move the top utilized Virtual Servers to a dedicated BIG-IP device. Where should the BIG-IP Administrator determine the problematic Virtual Servers? (Choose one answer)
- A. System > Platform
- B. Statistics > Module Statistics > Local Traffic > Virtual Servers
- C. Local Traffic > Network Map
- D. Local Traffic > Virtual Servers > Virtual Server List
Answer: B
Explanation:
Comprehensive and Detailed Explanation From BIG-IP Administration Data Plane Concepts documents:
When troubleshooting performance and latency issues on BIG-IP, especially under peak load conditions, it is critical to identify which Virtual Servers are consuming the most resources. This is a core data plane analysis task.
BIG-IP provides multiple views of configuration and status, but only certain areas expose real-time and historical traffic statistics that correlate directly with CPU usage and throughput.
Why Option C Is Correct:
Statistics > Module Statistics > Local Traffic > Virtual Servers provides:
Real-time and cumulative statistics per Virtual Server
Metrics such as:
Bits in / Bits out
Packets in / Packets out
Current connections
Connection rate
Total requests
The ability to identify high-traffic or high-connection Virtual Servers, which are the most likely contributors to elevated CPU utilization These statistics allow the administrator to objectively determine which Virtual Servers are the top consumers of system resources and therefore good candidates for migration to a dedicated BIG-IP device.
Why the Other Options Are Incorrect:
A . Local Traffic > Virtual Servers > Virtual Server List
Primarily a configuration view
Does not provide sufficient performance or utilization statistics to identify CPU-heavy Virtual Servers B . System > Platform Displays hardware-level information such as CPU cores, memory, disk, and platform type Does not break down utilization by Virtual Server D . Local Traffic > Network Map Provides a logical topology view of Virtual Servers, pools, and pool members Useful for understanding relationships, but not for identifying high-utilization Virtual Servers Key Data Plane Concept Reinforced:
To diagnose performance problems and plan traffic redistribution, BIG-IP administrators must rely on Module and object-level statistics, not configuration screens. The Virtual Server statistics view is the authoritative location for identifying traffic hotspots that directly impact CPU and latency during peak events such as Black Friday.
NEW QUESTION # 54
......
F5 F5CAB2 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
Get ready to pass the F5CAB2 Exam right now using our F5-CA Exam Package: https://examcollection.dumpsactual.com/F5CAB2-actualtests-dumps.html
